Matlab filter designer integrator code#

Therefore, the following piece of code calculates the tap number N: In the AD9361 Filter Guide, it says вЂњthe number of taps is configurable between a minimum of 16 taps and a maximum of 128 taps in groups of 16вЂќ. One other constraint about TFIR is the number of filter taps.

Wg2 = ( sqrt (FIR_interp )*wg1 )/ (dBinv (- dBstop ) ) Wg1 = abs (freqz (Filter1,omega (Gpass+ 2: end ),Fdac ).*analogresp ( 'Tx',omega (Gpass+ 2: end ),Fdac,b1,a1,b2,a2 ) ) On stopband, the required response rg = 0 and the weight w is: While on the Rx side, the ADC is represented by a sinc^3 function. On the Tx side, the DAC is represented by a sinc function. Please note the phase equalization process may take a few minutes, depending on the performance of your PC, since it tries to find a best target delay which yields the minimum group delay variance.ДЇor the analog filters, unlike digital filter, there is no вЂњcascadeвЂќ function to combine them and quickly calculate the composite response, so we made a helper function analogresp to calculate the overall response of the two analog filters and the converter.

Also note that when the design process completes, there is an updated target delay number (this number is 0 before phase equalization) shown in the вЂњFilter OptionsвЂќ portion. Comparing the group delay variance in the Results portion, it is decreased from 16.6 ns to 1.52 ns with phase equalization. The main purpose of the phase equalization is to reduce the pass band group delay *variance* brought by analog filters, digital filters and FIR filter, so that for signals at different frequencies, they will be delayed by an almost identical amount when going through the filter chain.ДЄfter you click вЂњDesign FilterвЂќ, the phase equalization part of the FIR design file is executed, and you will get an updated FIR filter design. Phase Equalization: If you would like to have the FIR filter do phase equalization, you can turn on the вЂњPhase EqualizationвЂќ option, as shown in the figure below. If you are mainly interested in pass band, click the top button, it will open the following three figures: One is from 0 Hz to half of the data rate, the other is from 0 Hz up to half of the converter rate.

For your convenience, we provide this tool on two different frequency scales. If you are interested in more details of the design performance, you can click the вЂњFVToolвЂќ buttons left to вЂњFilter ResultsвЂќ to launch the Filter Visualization Tool (fvtool) provided by The MathWorks. From these numbers, you will get an idea whether the design meets the requirements quantitatively. Below it, on the right, you will see a вЂњFilter ResultsвЂќ portion, where the actual Apass, Astop, the number of FIR taps and the pass band group delay variance are shown. The x-axis is from 0 to half of the data rate. If you are satisfied with all the parameters, you can go ahead and click вЂњDesign FilterвЂќ to start the design.ДЄs soon as the design process completes, you will see a magnitude plot displayed on the top half of the GUI, where the specified Fpass, Fstop, Apass and Astop are highlighted in the plot. There are three categories of input parameters: magnitude specifications, frequency specifications, and AD936x clock settings. In addition, you can also save your favorite parameter settings in this list, such as вЂњfoobar (Rx & Tx)вЂќ shown in the figure.ДЄssume that you choose the вЂњLTE10 (Rx & Tx)вЂќ profile, after you click it, all the parameters are filled in automatically for you, as shown in the figure below. Occupied RF Bandwidth from between 1.08MHz to 19.8MHz with 180kHz steps complies with the spec, and while these filters can be designed (manually) they are not included as defaults. The LTE Release-8 physical layer specification actually supports 105 different bandwidth options (not just the 6 shown above).

Matlab filter designer integrator